Quick Links to our
Product Range
Finally, a Ladder-Logic based PLC so small and cost so little that it can effectively replace all those bulky relays, timers or counters found in your current control panels. Its 24V DC transistor outputs or 0 to 250V AC relay outputs eliminate the need for additional driver circuitry and its incredibly low price means you actually save money while getting a technically superior design for your next control panel project!
With their built-in RS485 interface, the new E10+ PLCs are ideal for distributed control where the I/Os are distributed to far away locations. The RS485 standard interface allows a twisted pair wire to connect PLCs at up to 1200 m (4000 ft) away!
Up to 255 E10+ PLCs may be connected to a master PLC such as the T100MD+ or to a host PC using the Auto485. Each E10+ PLC can work standalone for fast local control and at the same time, their I/O status can be remotely controlled and monitored by the master PLC or by a PC. Its simple ASCII based Host Link Commands are really easy to use.
| Downloads: | Wiring Diagram JPEG (47KB) |
E10-npn+ Installation Guide  (133KB) |
E10-Relay+ Installation Guide (124KB) |
| ► | 12 to 24V DC Power Supply |
| ► | 6 Inputs with LED Indicators (12~24V DC, NPN type) |
| ► | 4 Outputs (each output can sink 1A @ 12~24V DC) |
| ► | 8 internal relays+2 internal outputs |
| ► | 4 timers (0.1s to 999.9s) 4 counters(1 to 9999) |
| ► | 1 sequencer with 32 steps (step# 0 - # 31) |
| ► | 216 program steps (1 contact = 1 step) Programmable in Ladder Logic software With SIMULATOR |
| ► | Creates ladder program using meaningful names |
| ► | Supports HostLink Command Protocol - The E10+ PLC can be used as a low cost I/O board for PC or other host processor board |
| ► | 24V AC or DC power supply (0.3A transformer) |
| ► | 6 Inputs with LED Indicators (24V DC, PNP type) |
| ► | 4 relay Outputs (2 commons. Each output can switch 2A @ 250V AC) |
| ► | Requires Opto232 adapter for programming by a PC |
| ► | All the rest are same as E10-NPN+ |
E10-Relay+ |
E10-npn+ |
|
| Power Supply |
- 24V AC (transformer) or 24VDC - Current = 0.2A - Rectified DC24V available for sensor |
- DC 12 to 24V (+ 10% ripple) - Current 0.5~2A (load dependent) |
CPU |
216 steps stored in EEPROM 20µs per step |
216 steps stored in EEPROM 20µs per step |
| Serial Interface | - 1 x TTL signal - 1 x RS485 port - Slave only mode. - Need Opto232 adapter to connect to PC |
- 1 x RS232 or RS485 port - Jumper selectable - Slave only mode. - Direct connection to PC |
| Input Circuits Number of inputs Input Voltage for Logic 0 Input Voltage for Logic 1 |
6 (PNP type) open circuit or 0 to 3.5V DC 8 to 24V DC |
6 (NPN type) open circuit or 8.5V to 24V 0V to +3.5V DC |
| Output Circuits Number of outputs Peak output current Output Voltage for Logic 1 Inductive back EMF protection |
4 2.0A @250VAC or 24VDC per output Dry contact ---- No---- |
4 Sink 1.0A per output 1.2V @ Iout = 500mA -----yes---- |
| Dimension | 7.8cm (L) x 5.6cm (W) x 2.5cm(H) | 5.4cm (L) x 5.4cm (W) x 2.0cm(H) |
| Weight (approximate) | 75g | 35g |